OP462HRUZ-REEL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | OP462 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 9V |
| Number of Channels | 4 |
| Operating Supply Current | 3.1mA |
| Nominal Supply Current | 2.8mA |
| Quiescent Current | 775μA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 260nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±1.35V~6V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 325μV |
| Bandwidth | 15MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 15000 kHz |
| Voltage Gain | 98.89dB |
| Average Bias Current-Max (IIB) | 0.65μA |
| Power Supply Rejection Ratio (PSRR) | 110dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 25μV |
| Settling Time | 475 ns |
| Bias Current-Max (IIB) @25C | 0.0006μA |
| Dual Supply Voltage | 5V |
| Height | 1mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
OP462HRUZ-REEL Overview
In the package, you will find a 14-TSSOP (0.173, 4.40mm Width)-case to contain the op amp ic. A General Purpose-type buffer amplifier is shown here. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. In recent months, the number of terminations has approached 14. A total of 14 pins are attached to buffer op amp. It is important to remember that this op amp should be operated at a voltage of 5V volts. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. It has 14 pins that make up the linear amplifier. Regarding input offset voltage, op amp rates 325μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. An 3.1mA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain at 98.89dB. There are 4 channels on the operational amplifiers. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 9V voltage. It is used TR to pack the op amps. As a result, linear amplifier's quiescent current is 775μA.
OP462HRUZ-REEL Features
14 Pins
supply voltage of 5V
98.89dB voltage gain
Output Type: Rail-to-Rail
OP462HRUZ-REEL Applications
There are a lot of Analog Devices Inc. OP462HRUZ-REEL Instrumentational OP Amps applications.
- Portable electronic products powered by batteries
- earphone
- MP3
- Signal amplification
- Polarized electrodes
- Proportional operation circuits
- Oscilloscopes
- Navigation
- High input resistance broadband
- single/dual op amp sum and difference circuits
