OP467GS-REEL
| Parameters | |
|---|---|
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | OP467 |
| Pin Count | 16 |
| Power Supplies | +-5/+-15V |
| Number of Channels | 4 |
| Operating Supply Current | 10mA |
| Quiescent Current | 8mA |
| Supply Current-Max | 13mA |
| Slew Rate | 350V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 150nA |
| Voltage - Supply, Single/Dual (±) | ±4.5V~18V |
| Input Offset Voltage (Vos) | 500μV |
| Gain Bandwidth Product | 28MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 22000 kHz |
| Voltage Gain | 83dB |
| Average Bias Current-Max (IIB) | 0.7μA |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 200μV |
| Settling Time | 200 ns |
| Bias Current-Max (IIB) @25C | 0.6μA |
| Input Capacitance | 2pF |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Input Voltage Noise Density | 7nV/sqrt Hz |
| Height Seated (Max) | 2.65mm |
| Length | 10.3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Operational Amplifier |
OP467GS-REEL Overview
A 16-SOIC (0.295, 7.50mm Width) case is used to package the op amp. Buffer amps of this type are called General Purpose-types. The op amp is delivered to you in a Tape & Reel (TR) case. It is estimated that there will be at least 16 terminations this year. There are a total of 16 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 5V volts. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. In total, the buffer amplifier consists of 16 pins. There is an input offset voltage of 500μV for this buffer op amp. For this electronic part, it is recommended that you mount it with type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. You can run this op amp ic on 10mA . Maintain 83dB as the voltage gain. Instrumentation amplifier has 4 channels on it. An buffer amplifier is packed in a TAPE AND REEL-shape according to the design. There is an 8mA quiescent current running through op amp ic.
OP467GS-REEL Features
16 Pins
supply voltage of 5V
83dB voltage gain
OP467GS-REEL Applications
There are a lot of Analog Devices Inc. OP467GS-REEL Instrumentational OP Amps applications.
- Tablets
- Proportional operation circuits
- Exponential operation circuits
- Comparator
- High gain DC amplifier
- Proportional counter tubes
- Vehicle electronics
- Weak signal detection
- High input resistance broadband
- E-book readers
