OP470EY
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Through Hole |
| Package / Case | 14-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 14 |
| Operating Temperature | -25°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | OP470 |
| Pin Count | 14 |
| Number of Channels | 4 |
| Operating Supply Current | 11mA |
| Nominal Supply Current | 11mA |
| Quiescent Current | 2.75mA |
| Slew Rate | 2V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 6nA |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Supply Type | Dual |
| Input Offset Voltage (Vos) | 400μV |
| Bandwidth | 6MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 6000 kHz |
| Voltage Gain | 127.23dB |
| Average Bias Current-Max (IIB) | 0.05μA |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 100μV |
| Settling Time | 6 μs |
| Bias Current-Max (IIB) @25C | 0.025μA |
| Dual Supply Voltage | 15V |
| Input Capacitance | 2pF |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Input Voltage Noise Density | 3.8nV/sqrt Hz |
| Height | 3.56mm |
| Length | 19.94mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
OP470EY Overview
In the package, you will find a 14-CDIP (0.300, 7.62mm)-case to contain the op amp ic. There are two types of operational amplifiers in this circuit. In the case of Tube cases, linear amplifier will be delivered. It is estimated that there will be at least 14 terminations this year. In this case, there are 14 pins on the board. As a reminder, this buffer op amp should be powered by 15V battery and that the battery should be inserted in the amplifier. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. 14 pins are included on the operational amplifiers. Op amp ic rates 400μV for input offset voltage. For this electrical component, the recommended mounting type is Through Hole, which is the most common. It is recommended that this op amp ic be operated at a temperature no higher than -25°C~85°C for optimal performance. An 11mA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain at 127.23dB. Op amp ic has 4 channels. As a result, linear amplifier's quiescent current is 2.75mA.
OP470EY Features
14 Pins
supply voltage of 15V
127.23dB voltage gain
OP470EY Applications
There are a lot of Analog Devices Inc. OP470EY Instrumentational OP Amps applications.
- Communication
- Blood pressure sensors
- Test and measurement instruments
- Radar
- Voltage regulation circuit
- Video amplifiers
- Computer workstations
- Laptop
- Micro signal measurement
- High input resistance broadband
