banner_page

OP484ESZ-REEL

4 Channels 10mA per Channel 80nA 90 dB Instrumentational OP Amps 0.575μA 28V 3V~36V ±1.5V~18V OP484 14 Pins 14-SOIC (0.154, 3.90mm Width)


  • Manufacturer: Analog Devices Inc.
  • Nocochips NO: 84-OP484ESZ-REEL
  • Package: 14-SOIC (0.154, 3.90mm Width)
  • Datasheet: PDF
  • Stock: 950
  • Description: 4 Channels 10mA per Channel 80nA 90 dB Instrumentational OP Amps 0.575μA 28V 3V~36V ±1.5V~18V OP484 14 Pins 14-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status PRODUCTION (Last Updated: 1 week ago)
Mounting Type Surface Mount
Package / Case 14-SOIC (0.154, 3.90mm Width)
Surface Mount YES
Number of Pins 14
Operating Temperature -40°C~125°C
Packaging Tape & Reel (TR)
JESD-609 Code e3
Pbfree Code no
Part Status Active
Moisture Sensitivity Level (MSL) 3 (168 Hours)
Number of Terminations 14
ECCN Code EAR99
Terminal Finish Matte Tin (Sn)
Subcategory Operational Amplifier
Packing Method TAPE AND REEL
Technology BIPOLAR
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 4
Supply Voltage 15V
Terminal Pitch 1.27mm
Time@Peak Reflow Temperature-Max (s) 30
Base Part Number OP484
Pin Count 14
Output Type Rail-to-Rail
Operating Supply Voltage 28V
Power Supplies +-1.5/+-18/3/36V
Number of Channels 4
Operating Supply Current 8mA
Nominal Supply Current 5.8mA
Quiescent Current 2mA
Slew Rate 4V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type General Purpose
Common Mode Rejection Ratio 90 dB
Current - Input Bias 80nA
Voltage - Supply, Single/Dual (±) 3V~36V ±1.5V~18V
Output Current per Channel 10mA
Supply Type Dual, Single
Input Offset Voltage (Vos) 150μV
Gain Bandwidth Product 4.25MHz
Neg Supply Voltage-Nom (Vsup) -15V
Unity Gain BW-Nom 4250 kHz
Voltage Gain 107.6dB
Average Bias Current-Max (IIB) 0.575μA
Power Supply Rejection Ratio (PSRR) 90dB
Low-Offset YES
Frequency Compensation YES
Supply Voltage Limit-Max 18V
Settling Time 4 μs
Dual Supply Voltage 15V
Input Voltage Noise Density 3.9nV/sqrt Hz
Height Seated (Max) 1.75mm
Length 8.65mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Lead Free Contains Lead

OP484ESZ-REEL Overview


It is packaged in an 14-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. There are two types of operational amplifiers in this circuit. A Tape & Reel (TR) case is used to deliver the buffer op amp. It is estimated that there will be 14 terminations in the next few months. A total of 14 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 14 pins are located on the operational amplifiers. The input offset voltage is 150μV. For this electrical component, Surface Mount is the recommended mounting type. With regard to operating temperature, op amp ranges -40°C~125°C. Using an 8mA supply current, this operational amplifier ics can be operated. It is a member of the 107.6dB's 107.6dB family. Op amp ic has 4 channels. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of instrumentation amplifier is rated 28V voltage. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. The current is quiescent at 2mA.

OP484ESZ-REEL Features


14 Pins
supply voltage of 15V
107.6dB voltage gain
Output Type: Rail-to-Rail

OP484ESZ-REEL Applications


There are a lot of Analog Devices Inc. OP484ESZ-REEL Instrumentational OP Amps applications.

  • Proportional counter tubes
  • Micro signal measurement
  • Automatic control
  • Digital cameras
  • Scintillation detectors
  • Multiplication circuits
  • Band-pass filter
  • Information processing
  • Navigation
  • High gain DC amplifier

Write a review

Note: HTML is not translated!
    Bad           Good