OP484FS-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | OP484 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 28V |
| Power Supplies | +-1.5/+-18/3/36V |
| Number of Channels | 4 |
| Operating Supply Current | 2.25mA |
| Nominal Supply Current | 5.8mA |
| Quiescent Current | 2mA |
| Slew Rate | 4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 80nA |
| Voltage - Supply, Single/Dual (±) | 3V~36V ±1.5V~18V |
| Output Current per Channel | 10mA |
| Supply Type | Dual, Single |
| Input Offset Voltage (Vos) | 250μV |
| Gain Bandwidth Product | 4.25MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4250 kHz |
| Voltage Gain | 107.6dB |
| Average Bias Current-Max (IIB) | 0.575μA |
| Power Supply Rejection Ratio (PSRR) | 76dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Dual Supply Voltage | 15V |
| Input Voltage Noise Density | 3.9nV/sqrt Hz |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
OP484FS-REEL Overview
Packaging for the buffer amplifier is in the form of a 14-SOIC (0.154, 3.90mm Width) case. Buffer amps of this type are called General Purpose-types. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. It is estimated that there will be at least 14 terminations this year. A total of 14 pins are located on this board. Please take in mind that this instrumentation amplifier should be run at 15V. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. It has 14 pins that make up the linear amplifier. The input offset voltage is 250μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. Operational amplifier can operate supply current at 2.25mA. The voltage gain should stay at 107.6dB. There are 4 channels on the operational amplifiers. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 28V. The linear amplifier is packaged by using a TAPE AND REEL axis. As a result, linear amplifier's quiescent current is 2mA.
OP484FS-REEL Features
14 Pins
supply voltage of 15V
107.6dB voltage gain
Output Type: Rail-to-Rail
OP484FS-REEL Applications
There are a lot of Analog Devices Inc. OP484FS-REEL Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- Ultrasound transducers
- Large motor controllers
- Automatic control
- Automotive sensors
- PDA
- Power transmission
- single/dual op amp sum and difference circuits
- High speed sample
- Signal operation
