OP492GSZ-REEL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | OP492 |
| Pin Count | 14 |
| Operating Supply Voltage | 28V |
| Power Supplies | +-15V |
| Number of Channels | 4 |
| Operating Supply Current | 5.6mA |
| Nominal Supply Current | 4.8mA |
| Quiescent Current | 1.4mA |
| Slew Rate | 4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 375nA |
| Voltage - Supply, Single/Dual (±) | 4.5V~33V ±2.25V~16.5V |
| Output Current per Channel | 10.5mA |
| Input Offset Voltage (Vos) | 2.5mV |
| Gain Bandwidth Product | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 5μA |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 33V |
| Voltage - Input Offset | 1.4mV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.7μA |
| Programmable Power | NO |
| Wideband | NO |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
OP492GSZ-REEL Overview
In the package, you will find a 14-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. Op amps are General Purpose types of amplifier on the chip. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. In recent months, the number of terminations has approached 14. Buffer amplifier has a total of 14 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. There are 14 pins on this chip. In terms of the input offset voltage, instrumentation amplifier rates at 2.5mV. This electronic part is best mounted with type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. Operational amplifier can operate supply current at 5.6mA. Voltage gain should remain at 106.02dB. Op amp ic has 4 channels. The operating supply voltage of instrumentation amplifier is rated 28V voltage. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted. Buffer amplifier has a quiescent current of 1.4mA.
OP492GSZ-REEL Features
14 Pins
supply voltage of 5V
106.02dB voltage gain
OP492GSZ-REEL Applications
There are a lot of Analog Devices Inc. OP492GSZ-REEL Instrumentational OP Amps applications.
- High/low-pass filter circuit
- Weighing systems
- Vehicle electronics
- Portable media players
- Fission chambers
- Addition operation circuits
- Portable electronic products powered by batteries
- Proportional operation circuits
- Oscilloscopes
- Car stereo
