OP497FS
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 220 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | OP497 |
| Pin Count | 16 |
| Power Supplies | +-15V |
| Number of Channels | 4 |
| Operating Supply Current | 2.5mA |
| Nominal Supply Current | 2.5mA |
| Max Supply Current | 2.5mA |
| Quiescent Current | 625μA |
| Slew Rate | 0.15V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 135 dB |
| Current - Input Bias | 40pA |
| Voltage - Supply, Single/Dual (±) | ±2V~20V |
| Output Current per Channel | 25mA |
| Supply Type | Dual |
| Input Offset Voltage (Vos) | 75μV |
| Gain Bandwidth Product | 500kHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 500 kHz |
| Voltage Gain | 132.04dB |
| Average Bias Current-Max (IIB) | 0.0002μA |
| Power Supply Rejection Ratio (PSRR) | 135dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 20V |
| Voltage - Input Offset | 40μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00015μA |
| Dual Supply Voltage | 18V |
| Input Capacitance | 3pF |
| Neg Supply Voltage-Max (Vsup) | -20V |
| Input Voltage Noise Density | 17nV/sqrt Hz |
| Height | 2.35mm |
| Length | 10.5mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
OP497FS Overview
The linear amplifier is packaged in a 16-SOIC (0.295, 7.50mm Width) case. A General Purpose-type buffer amplifier is shown here. Instrumentation amplifier is delivered in a Tube case. The number of terminations approaches 16. The pins on this board total to 16 in total. I would like to remind you that this buffer op amp should be powered by an 15V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 16 pins are located on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 75μV. For this electronic part, it is recommended that you mount it with type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~85°C. An 2.5mA volt supply current is needed for this linear amplifier to operate. Op amp is a member of the 132.04dB's 132.04dB family. 4 channels are available on the instrumentation amplifier. The quiescent current is 625μA.
OP497FS Features
16 Pins
supply voltage of 15V
132.04dB voltage gain
OP497FS Applications
There are a lot of Analog Devices Inc. OP497FS Instrumentational OP Amps applications.
- Computer workstations
- RF cable systems
- Proportional operation circuits
- Automotive sensors
- Multiplication circuits
- Switching amplifier
- Commercial audio systems
- Power generator
- Video data acquisition
- Large motor controllers
