OP77FJZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | TO-99-8 Metal Can |
| Number of Pins | 8 |
| Supplier Device Package | TO-99-8 |
| Operating Temperature | -25°C~85°C |
| Packaging | Bulk |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Max Power Dissipation | 60mW |
| Base Part Number | OP77 |
| Number of Elements | 1 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 2mA |
| Nominal Supply Current | 2mA |
| Quiescent Current | 2mA |
| Slew Rate | 0.3V/μs |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 140 dB |
| Current - Input Bias | 1.2nA |
| Voltage - Supply, Single/Dual (±) | ±3V~18V |
| Input Offset Voltage (Vos) | 25μV |
| Bandwidth | 600 kHz |
| Gain Bandwidth Product | 600kHz |
| Voltage Gain | 135.56dB |
| Power Supply Rejection Ratio (PSRR) | 123dB |
| Voltage - Input Offset | 20μV |
| Max Dual Supply Voltage | 22V |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 9V |
| Input Voltage Noise Density | 10.5nV/sqrt Hz |
| Number of Amplifiers | 1 |
| Height | 4.7mm |
| Length | 9.4mm |
| Width | 9.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
OP77FJZ Overview
Packaging for the buffer amplifier is in the form of a TO-99-8 Metal Can case. This is a General Purpose type op amp. There is a Bulk case that is delivered with the instrumentation amplifiers. The op amp ic has an array of 8 pins on it. There is an input offset voltage of 25μV for this buffer op amp. This electronic component is recommended to be mounted using the mounting type Through Hole. It is important to note that this linear amplifier works well at a temperature of -25°C~85°C when it comes to operating temperatureIt is possible to operate this buffer amplifier from a supply current of 2mA . There should be no change in the voltage gain. A instrumentation amplifier like this has 1 circuits. Buffer op amp is equipped with 1 channels on the device. To operate this buffer amplifier, the temperature must not be lower than -55°C. Linear amplifier shouldn't be used above 125°C degrees. The total number of elements in this buffer amplifier is 1. This electric component can work from a voltage of under 18V as far as supply voltage is concerned. As a rule of thumb, the supply voltage of the op amp should not be lower than 3V. The dual supply voltage of 22V should be used for the conduct of this electronic component. There is an 2mA quiescent current running through op amp ic. The linear amplifier has 1 amplifiers.
OP77FJZ Features
135.56dB voltage gain
OP77FJZ Applications
There are a lot of Analog Devices Inc. OP77FJZ Instrumentational OP Amps applications.
- Vehicle electronics
- Communication device
- Gaming industry
- Portable docking station
- Micro signal measurement
- Digital cameras
- Multimedia playback equipment
- Mobile phone
- Fast A/D and D/A converters
- Differentiator circuits
