OP97FS-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | OP97 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 600μA |
| Quiescent Current | 600μA |
| Slew Rate | 0.2V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 132 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | ±2V~20V |
| Input Offset Voltage (Vos) | 25μV |
| Gain Bandwidth Product | 900 kHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 900 kHz |
| Voltage Gain | 126.02dB |
| Average Bias Current-Max (IIB) | 0.00075μA |
| Power Supply Rejection Ratio (PSRR) | 132dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 20V |
| Voltage - Input Offset | 30μV |
| Low-Bias | YES |
| Micropower | YES |
| Dual Supply Voltage | 15V |
| Neg Supply Voltage-Max (Vsup) | -20V |
| Input Voltage Noise Density | 17nV/sqrt Hz |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
OP97FS-REEL Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. General Purpose-type instrumentation amplifiers are used in this application. A Tape & Reel (TR) case is used for delivering the op amp. It is estimated that there will be at least 8 terminations this year. The total number of pins on linear amplifier is 8. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. An 8-pin op amp ic is included in the package. With regards to the offset voltage of the input, buffer amplifier is rated at 25μV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. In order for this instrumentation amplifier to operate, the supply current needs to be between 600μA and 10 . There should be no change in the voltage gain at 126.02dB. There are 1 channels on the operational amplifiers. The quiescent current is 600μA.
OP97FS-REEL Features
8 Pins
supply voltage of 15V
126.02dB voltage gain
OP97FS-REEL Applications
There are a lot of Analog Devices Inc. OP97FS-REEL Instrumentational OP Amps applications.
- Power control
- Laptop
- Industrial control system
- High speed sample
- Band-stop filter
- Thermocouples
- Vehicle electronics
- Tablets
- Television broadcasting equipment
- Integrator circuits
