OPA130UAE4
| Parameters | |
|---|---|
| Slew Rate | 2 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 20pA |
| Output Current per Channel | 18mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 1MHz |
| Gain Bandwidth Product | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 135dB |
| Average Bias Current-Max (IIB) | 0.00002μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 18V |
| Low-Bias | YES |
| Micropower | YES |
| Min Dual Supply Voltage | 2.25V |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 1mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.00002μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Package / Case | SOIC |
| Surface Mount | YES |
| Number of Pins | 8 |
| Packaging | Rail/Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Temperature Grade | AUTOMOTIVE |
| Number of Circuits | 1 |
| Operating Supply Current | 530μA |
| Nominal Supply Current | 650μA |
OPA130UAE4 Overview
Op amp is packaged in SOIC case. Op amps are OPERATIONAL AMPLIFIER types of amplifier on the chip. Instrumentation amplifier is delivered in a Rail/Tube case. There have been a total of 8 terminations over the past year. The pins on this board total to 8 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. Linear amplifier includes 8 pins. In terms of the input offset voltage, instrumentation amplifier rates at 1mV. Using a supply current of 530μA , this buffer op amp will be able to operate. Op amp is a member of the 135dB's 135dB family. In total, there are 1 circuits on this buffer amplifier. It is recommended that the temperature of this op amp ic should not fall below -40°C degrees Fahrenheit at any time. You should only use op amp buffer at temperatures that are no higher than 125°C. The operating supply voltage of instrumentation amplifier is rated 18V voltage. As a rule of thumb, you should conduct this electronic part under a dual voltage supply of 18V volts.
OPA130UAE4 Features
8 Pins
supply voltage of 15V
135dB voltage gain
OPA130UAE4 Applications
There are a lot of Texas Instruments OPA130UAE4 Instrumentational OP Amps applications.
- Commercial audio systems
- Hand-held batteries
- High speed sample
- Radiation thermometry transducers
- Wireless base stations
- Portable electronic products powered by batteries
- Measurements of Wheatstone bridge
- Division circuits
- Image computer boards
- Thermocouples
