OPA131U
| Parameters | |
|---|---|
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | OPA131 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Operating Supply Current | 1.5mA |
| Nominal Supply Current | 1.75mA |
| Output Current | 25mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 750μV |
| Bandwidth | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 200μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Nominal Gain Bandwidth Product | 4MHz |
| Max I/O Voltage | 750μV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
OPA131U Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. An op amp of this type is a General Purpose-type. In the case of Tube cases, linear amplifier will be delivered. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are attached to buffer op amp. It is important to remember that this op amp should be operated at a voltage of 15V volts. To be specific, this instrumentation amplifier is a type of Operational Amplifier. It has 8 pins that make up the linear amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 750μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. A supply current of 1.5mA can be used to operate this linear amplifier. 110dB should remain the voltage gain. On the buffer amps, there are 1 channels that can be used. The operating supply voltage of the buffer op amp is rated at 18V.
OPA131U Features
8 Pins
supply voltage of 15V
110dB voltage gain
OPA131U Applications
There are a lot of Texas Instruments OPA131U Instrumentational OP Amps applications.
- Test and measurement instruments
- Car stereo
- Multiplication circuits
- Active probe
- Communication
- High speed sample
- Fission chambers
- Commercial audio systems
- Tablets
- Video amplifiers
