OPA131UJ/2K5
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | OPA131 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Elements | 1 |
| Nominal Supply Current | 2mA |
| Output Current | 25mA |
| Current - Supply | 1.5mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Input Offset Voltage (Vos) | 1.5mV |
| Bandwidth | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 200μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Nominal Gain Bandwidth Product | 4MHz |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA131UJ/2K5 Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. An op amp of this type is a General Purpose-type. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. There have been a total of 8 terminations over the past year. It consists of a total of 8 pins in total. This linear amplifier should be powered by an 15V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 8 pins are available on the instrumentation amplifier. Regarding input offset voltage, op amp rates 1.5mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. It is recommended to keep the voltage gain at 110dB at all times. The total number of elements in this buffer amplifier is 1. The operating supply voltage of the buffer op amp is rated at 18V. This linear amplifier pack is based on the TR axis. It is recommended that this electronic component be used with an 1.5mA supply.
OPA131UJ/2K5 Features
8 Pins
supply voltage of 15V
110dB voltage gain
OPA131UJ/2K5 Applications
There are a lot of Texas Instruments OPA131UJ/2K5 Instrumentational OP Amps applications.
- Exponential operation circuits
- Comparator
- Weak signal detection
- Differentiator circuits
- RF cable systems
- Ultrasound transducers
- Laptop
- Voltage regulation circuit
- Logarithmic operation circuits
- Car stereo
