OPA134UAE4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 75.891673mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Series | SoundPlus™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | OPA134 |
| Pin Count | 8 |
| Operating Supply Voltage | 36V |
| Number of Elements | 1 |
| Operating Supply Current | 4mA |
| Nominal Supply Current | 5mA |
| Slew Rate | 20V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Audio |
| Common Mode Rejection Ratio | 86 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 5V~36V ±2.5V~18V |
| Output Current per Channel | 35mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 8MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 8000 kHz |
| Voltage Gain | 120dB |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 8MHz |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA134UAE4 Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. This is a Audio type op amp. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. The number of terminations approaches 8. There are a total of 8 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 15V volts. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. The op amp ic has an array of 8 pins on it. With regards to the offset voltage of the input, buffer amplifier is rated at 2mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. A supply current of 4mA can be used to operate this linear amplifier. It is a member of the 120dB's 120dB family. 1 elements make up the design of this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 36V. The SoundPlus? represents the op amp's series number.
OPA134UAE4 Features
8 Pins
supply voltage of 15V
120dB voltage gain
OPA134UAE4 Applications
There are a lot of Texas Instruments OPA134UAE4 Instrumentational OP Amps applications.
- Measurements of Wheatstone bridge
- Differentiator circuits
- Television broadcasting equipment
- Biopotential
- Weighing systems
- ECG equipment
- Proportional counter tubes
- Non-polarized electrodes
- Logarithmic operation circuits
- Integrator circuits
