OPA137P
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Series | MicroAmplifier™ |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | OPA137 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Elements | 1 |
| Operating Supply Current | 220μA |
| Nominal Supply Current | 270μA |
| Output Current | 60mA |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 76 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±2.25V~18V |
| Output Current per Channel | 60mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 94dB |
| Power Supply Rejection Ratio (PSRR) | 80.92dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.5mV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 3mV |
| Height | 4.57mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA137P Overview
A 8-DIP (0.300, 7.62mm) case is used to package the op amp. An op amp of this type is a General Purpose-type. In the case of Tube cases, linear amplifier will be delivered. The number of terminations approaches 8. There are a total of 8 pins on this op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. It should be noted that this op amp is a type of Operational Amplifier device. A total of 8 pins are present on the instrumentation amplifier. Regarding input offset voltage, buffer amplifier rates 3mV voltage. This electronic part is recommended for mounting type Through Hole. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. Operational amplifier can operate supply current at 220μA. Voltage gain should remain at 94dB. A total of 1 elements are present in this linear amplifier. The operating supply voltage of the buffer op amp is rated at 18V. MicroAmplifier? corresponds to linear amplifier's series.
OPA137P Features
8 Pins
supply voltage of 15V
94dB voltage gain
OPA137P Applications
There are a lot of Texas Instruments OPA137P Instrumentational OP Amps applications.
- Test and measurement instruments
- High/low-pass filter circuit
- Thermocouples
- Switching amplifier
- Portable docking station
- Logarithmic operation circuits
- Power generator
- Video data acquisition
- Medical instruments
- Signal amplification
