OPA137U
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Series | MicroAmplifier™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | OPA137 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Operating Supply Current | 220μA |
| Nominal Supply Current | 270μA |
| Output Current | 60mA |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 76 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±2.25V~18V |
| Output Current per Channel | 60mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 94dB |
| Power Supply Rejection Ratio (PSRR) | 80.92dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.5mV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 3mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA137U Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case. Buffer amps of this type are called General Purpose-types. The case in which buffer amplifier is delivered is called a Tube case. There have been a total of 8 terminations over the past year. There are a total of 8 pins on this op amp. I would like to remind you that this buffer op amp should be powered by an 15V battery. Instrumentation amplifier is a part of Operational Amplifier. Linear amplifier includes 8 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 3mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureOperational amplifier can operate supply current at 220μA. Op amp is a member of the 94dB's 94dB family. On the buffer amps, there are 1 channels that can be used. The operating supply voltage of the buffer op amp is rated at 18V. As the name implies, MicroAmplifier? refers to the series of the buffer op amp.
OPA137U Features
8 Pins
supply voltage of 15V
94dB voltage gain
OPA137U Applications
There are a lot of Texas Instruments OPA137U Instrumentational OP Amps applications.
- Signal operation
- Communication
- Differentiator circuits
- Video amplifiers
- Voltage regulation circuit
- Information processing
- Television broadcasting equipment
- High input resistance broadband
- Large motor controllers
- Ultrasound transducers
