OPA1602AIDGKR
| Parameters | |
|---|---|
| Current - Input Bias | 20nA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±2.25V~18V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 1mV |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 35000 kHz |
| Voltage Gain | 120dB |
| Power Supply Rejection Ratio (PSRR) | 126.02dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 100μV |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 35MHz |
| Max I/O Voltage | 1mV |
| Wideband | NO |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| Series | SoundPlus™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | OPA1602 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 36V |
| Number of Elements | 2 |
| Operating Supply Current | 2.6mA |
| Nominal Supply Current | 2.6mA |
| Slew Rate | 20V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Audio |
| Common Mode Rejection Ratio | 114 dB |
OPA1602AIDGKR Overview
It is packaged in an 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case that protects the operational amplifiers from damage. Op amps are Audio types of amplifier on the chip. A Cut Tape (CT) case is used to deliver the buffer op amp. We are approaching the 8h termination of the year. The pins on this board total to 8 in total. It is important to remember that this op amp should be operated at a voltage of 15V volts. To be specific, this instrumentation amplifier is a type of Operational Amplifier. In total, the buffer amplifier consists of 8 pins. As far as the input offset voltage is concerned, linear amplifier rates at 1mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. You can run this op amp ic on 2.6mA . There should be no change in the voltage gain at 120dB. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. As a whole, there are 2 elements that make up this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 36V voltage. The linear amplifier is packaged by using a TR axis. The SoundPlus? indicates the series number of the op amp.
OPA1602AIDGKR Features
8 Pins
supply voltage of 15V
120dB voltage gain
Output Type: Rail-to-Rail
OPA1602AIDGKR Applications
There are a lot of Texas Instruments OPA1602AIDGKR Instrumentational OP Amps applications.
- Automation control systems
- Biopotential
- RF cable systems
- Active probe
- High/low-pass filter circuit
- E-book readers
- Radiation thermometry transducers
- Proportional operation circuits
- Thermocouples
- Test equipment
