Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 3 days ago) |
Contact Plating |
Gold |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Operating Temperature |
-40°C~125°C |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
2 (1 Year) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Subcategory |
Operational Amplifier |
Packing Method |
TR |
Technology |
BIPOLAR |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
18V |
Base Part Number |
OPA170 |
Pin Count |
8 |
Output Type |
Rail-to-Rail |
Operating Supply Voltage |
18V |
Number of Elements |
1 |
Operating Supply Current |
110μA |
Nominal Supply Current |
110μA |
Output Current |
17mA |
Slew Rate |
0.4V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
104 dB |
Current - Input Bias |
8pA |
Voltage - Supply, Single/Dual (±) |
2.7V~36V ±1.35V~18V |
Output Current per Channel |
20mA |
Input Offset Voltage (Vos) |
1.8mV |
Neg Supply Voltage-Nom (Vsup) |
-18V |
Unity Gain BW-Nom |
1200 kHz |
Voltage Gain |
130dB |
Average Bias Current-Max (IIB) |
0.0035μA |
Power Supply Rejection Ratio (PSRR) |
120dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
20V |
Voltage - Input Offset |
250μV |
Low-Bias |
YES |
Micropower |
YES |
Programmable Power |
NO |
Nominal Gain Bandwidth Product |
1.2MHz |
Max I/O Voltage |
1.8mV |
Wideband |
NO |
Input Offset Current-Max (IIO) |
0.0035μA |
Height |
1.75mm |
Length |
4.9mm |
Width |
3.91mm |
Thickness |
1.58mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
OPA170AIDR Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case which makes it easy for the consumer to handle. Op amps are General Purpose types of amplifier on the chip. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. We are approaching the 8h termination of the year. A total of 8 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 18V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. In total, the buffer amplifier consists of 8 pins. Regarding input offset voltage, buffer amplifier rates 1.8mV voltage. For this electrical component, Surface Mount is the recommended mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. As long as the supply current of the chip does not exceed 110μA, this op amp ic can operate. It is recommended to keep the voltage gain at 130dB at all times. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. 1 elements make up the design of this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 18V. For the packing of the instrumentation amplifier, TR is adopted.
OPA170AIDR Features
8 Pins
supply voltage of 18V
130dB voltage gain
Output Type: Rail-to-Rail
OPA170AIDR Applications
There are a lot of Texas Instruments OPA170AIDR Instrumentational OP Amps applications.
- Ultrasound transducers
- Hand-held batteries
- Exponential operation circuits
- Inverse/same-phase proportional circuit
- Power transmission
- Band-pass filter
- Power generator
- E-book readers
- Test and measurement instruments
- Weighing systems