OPA177GPG4
| Parameters | |
|---|---|
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | OPA177 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Operating Supply Current | 1.3mA |
| Nominal Supply Current | 1.5mA |
| Slew Rate | 0.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 115 dB |
| Current - Input Bias | 500pA |
| Voltage - Supply, Single/Dual (±) | 6V~36V ±3V~18V |
| Input Offset Voltage (Vos) | 60μV |
| Bandwidth | 600 kHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 600 kHz |
| Voltage Gain | 135.56dB |
| Average Bias Current-Max (IIB) | 0.002μA |
| Power Supply Rejection Ratio (PSRR) | 110dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 22V |
| Voltage - Input Offset | 20μV |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 600 kHz |
| Max I/O Voltage | 60μV |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
OPA177GPG4 Overview
The linear amplifier is packaged in a 8-DIP (0.300, 7.62mm) case which makes it easy for the consumer to handle. An op amp ic of the General Purpose type. A Tube case is used to deliver the buffer op amp. A total of 8 terminations have been reported in the past few weeks. The pins on this board total to 8 in total. Please take in mind that this instrumentation amplifier should be run at 15V. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. In total, the buffer amplifier consists of 8 pins. There is an input offset voltage of 60μV for this buffer op amp. It is recommended that this electronic component be mounted using the Through Hole mounting type. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. As long as the supply current of the chip does not exceed 1.3mA, this op amp ic can operate. 135.56dB should remain the voltage gain. 1 channels are available on the instrumentation amplifier. The operating supply voltage of instrumentation amplifier is rated 18V voltage.
OPA177GPG4 Features
8 Pins
supply voltage of 15V
135.56dB voltage gain
OPA177GPG4 Applications
There are a lot of Texas Instruments OPA177GPG4 Instrumentational OP Amps applications.
- Communication
- Exponential operation circuits
- E-book readers
- Fission chambers
- Video conversion and routing
- Oscilloscopes
- Power transmission
- Radiation thermometry transducers
- Micro signal measurement
- Laptop
