OPA192ID
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Series | e-trim™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | OPA192 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Circuits | 1 |
| Operating Supply Current | 1mA |
| Slew Rate | 20V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 8V~36V ±4V~18V |
| Output Current per Channel | 65mA |
| Input Offset Voltage (Vos) | 5μV |
| Gain Bandwidth Product | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 140dB |
| Average Bias Current-Max (IIB) | 0.00002μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 20V |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00002μA |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -20V |
| Wideband | NO |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.002μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA192ID Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. The instrumentation amplifier in this picture is of the General Purpose-type. Upon delivery, op amp ic is packaged in a Tube case. There is a growing number of terminations approaching the number of 8. The pins on this board total to 8 in total. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 8 pins are included on the operational amplifiers. Regarding input offset voltage, op amp rates 5μV. For this electronic part, it is recommended that you mount it with type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureThis op amp can operate from a supply current at 1mA. Voltage gain should remain at 140dB. This op amp contains 1 circuits. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. e-trim? corresponds to the op amp's series.
OPA192ID Features
8 Pins
140dB voltage gain
Output Type: Rail-to-Rail
OPA192ID Applications
There are a lot of Texas Instruments OPA192ID Instrumentational OP Amps applications.
- Thermocouples
- Proportional operation circuits
- ECG equipment
- Inverse/same-phase proportional circuit
- Multiplication circuits
- Power generator
- Weak signal detection
- Portable electronic products powered by batteries
- Comparator
- Displayers for aircraft and air transportation control systems
