OPA2130UA
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | OPA2130 |
| Pin Count | 8 |
| Power Supplies | +-15V |
| Number of Channels | 2 |
| Operating Supply Current | 530μA |
| Nominal Supply Current | 530μA |
| Slew Rate | 2V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±2.25V~18V |
| Output Current per Channel | 18mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 135dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 200μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 1mV |
| Power | NO |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2130UA Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case. The instrumentation amplifier in this picture is of the General Purpose-type. In the case of Tube cases, linear amplifier will be delivered. It is estimated that there will be 8 terminations in the next few months. The pins on this board total to 8 in total. Please take in mind that op amp should be run at 15V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. A total of 8 pins are present on the instrumentation amplifier. Regarding input offset voltage, op amp rates 1mV. The mounting type that is recommended for this electrical part is Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~85°C. You can run this op amp ic on 530μA . 135dB should be the voltage gain. There are 2 channels on the operational amplifiers.
OPA2130UA Features
8 Pins
supply voltage of 15V
135dB voltage gain
OPA2130UA Applications
There are a lot of Texas Instruments OPA2130UA Instrumentational OP Amps applications.
- Tablets
- Power transmission
- Information processing
- Active probe
- pH (acidity)
- Industrial control system
- Signal transformation
- Portable electronic products powered by batteries
- Proportional operation circuits
- Test equipment
