OPA2132UA
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 75.891673mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | OPA2132 |
| Pin Count | 8 |
| Number of Channels | 2 |
| Operating Supply Current | 4mA |
| Nominal Supply Current | 4mA |
| Slew Rate | 20V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 86 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 5V~36V ±2.5V~18V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 8MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 8000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Nominal Gain Bandwidth Product | 8MHz |
| Max I/O Voltage | 2mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Input Voltage Noise Density | 23nV/sqrt Hz |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2132UA Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. There are two types of operational amplifiers in this circuit. Instrumentation amplifier is delivered in a Tube case. A total of 8 terminations have been reported in the past few weeks. In total, there are 8 pins on this op amp ic. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. An 8-pin op amp ic is included in the package. There is an input offset voltage of 500μV for this buffer op amp. Surface Mount is the recommended mounting type of operational amplifiers. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~85°C . A supply current of 4mA can be used to operate this linear amplifier. There should be no change in the voltage gain. As far as the device is concerned, buffer amplifier has 2 channels.
OPA2132UA Features
8 Pins
supply voltage of 15V
120dB voltage gain
OPA2132UA Applications
There are a lot of Texas Instruments OPA2132UA Instrumentational OP Amps applications.
- Vehicle electronics
- Subtraction operation circuits
- Switching amplifier
- Micro signal measurement
- Ultrasound transducers
- Television
- Signal filtering
- Comparator
- Weak signal detection
- Communication device
