OPA2137EA/250
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Series | MicroAmplifier™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | OPA2137 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Nominal Supply Current | 220μA |
| Output Current | 60mA |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 76 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±2.25V~18V |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 94dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Power Supply Rejection Ratio (PSRR) | 80.92dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 2.5mV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 3mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2137EA/250 Overview
There is a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case in which the instrumentation amplifier is packaged. A General Purpose-type buffer amplifier is shown here. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. There is a growing number of terminations approaching the number of 8. Linear amplifier has a total of 8 pins. Please take in mind that op amp should be run at 15V. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. The buffer op amp includes 8 pins. In terms of input offset voltage, operational amplifier rates 10mV. Surface Mount is the recommended mounting type for this linear amplifier. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. There should be no change in the voltage gain. On this instrumentation amplifier, there are 2 circuits that are connected together. The op amp ic has 2 channels on it. The operating supply voltage of instrumentation amplifier is rated 18V voltage. The instrumentation amplifier is packed in the form of TR. MicroAmplifier? is the number that corresponds to the series of the buffer op amp.
OPA2137EA/250 Features
8 Pins
supply voltage of 15V
94dB voltage gain
OPA2137EA/250 Applications
There are a lot of Texas Instruments OPA2137EA/250 Instrumentational OP Amps applications.
- Digital cameras
- Weak signal detection
- Broadcasting
- Hand-held batteries
- Power transmission
- Medical instruments
- Power control
- Differentiator circuits
- PDA
- pH (acidity)
