OPA2137UA/2K5
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Series | MicroAmplifier™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | OPA2137 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Elements | 2 |
| Number of Circuits | 2 |
| Nominal Supply Current | 220μA |
| Output Current | 60mA |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±2.25V~18V |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 94dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Power Supply Rejection Ratio (PSRR) | 80.92dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 2.5mV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 3mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2137UA/2K5 Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. Buffer amps of this type are called General Purpose-types. A Tape & Reel (TR) case is used for delivering the op amp. There is a growing number of terminations approaching the number of 8. A total of 8 pins are attached to buffer op amp. It is important to remember that this op amp should be operated at a voltage of 15V volts. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 8 pins are available on the instrumentation amplifier. Regarding input offset voltage, op amp rates 10mV. For this electrical component, Surface Mount is the recommended mounting type. With regard to operating temperature, this op amp functions well at -40°C~85°C. Voltage gain should remain at 94dB. A linear amplifier like this has 2 circuits on it. There are a total of 2 elements in this linear amplifier. The operating supply voltage of instrumentation amplifier is rated 18V voltage. For the packing of the instrumentation amplifier, TR is adopted. Instrumentation amplifiers are numbered by their MicroAmplifier? series.
OPA2137UA/2K5 Features
8 Pins
supply voltage of 15V
94dB voltage gain
OPA2137UA/2K5 Applications
There are a lot of Texas Instruments OPA2137UA/2K5 Instrumentational OP Amps applications.
- Voltage regulation circuit
- Laptop
- Micro signal measurement
- Large motor controllers
- Medical imaging
- Weighing systems
- Power generator
- Proportional counter tubes
- Signal transformation
- Exponential operation circuits
