OPA2170AIDR
| Parameters | |
|---|---|
| Slew Rate | 0.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 104 dB |
| Current - Input Bias | 8pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~36V ±1.35V~18V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 1.8mV |
| Bandwidth | 1.2MHz |
| Neg Supply Voltage-Nom (Vsup) | -18V |
| Unity Gain BW-Nom | 1200 kHz |
| Voltage Gain | 130dB |
| Average Bias Current-Max (IIB) | 0.0035μA |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 250μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.000015μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1.2MHz |
| Max I/O Voltage | 1.8mV |
| Input Offset Current-Max (IIO) | 0.0035μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 18V |
| Base Part Number | OPA2170 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 18V |
| Number of Channels | 2 |
| Operating Supply Current | 110μA |
| Nominal Supply Current | 110μA |
| Output Current | 17mA |
OPA2170AIDR Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. A General Purpose-type buffer amplifier is shown here. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. During the past two weeks, there have been close to 8 terminations. In this case, there are 8 pins on the board. I would like to remind you that this buffer op amp should be powered by an 18V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. The op amp ic has an array of 8 pins on it. Regarding input offset voltage, op amp rates 1.8mV. Surface Mount is the recommended mounting type for this linear amplifier. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . As long as the supply current of the chip does not exceed 110μA, this op amp ic can operate. It is a member of the 130dB's 130dB family. As far as the device is concerned, buffer amplifier has 2 channels. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. The operating supply voltage of instrumentation amplifier is rated 18V voltage. To pack the operational amplifier ics, TR is adopted as the packing method.
OPA2170AIDR Features
8 Pins
supply voltage of 18V
130dB voltage gain
Output Type: Rail-to-Rail
OPA2170AIDR Applications
There are a lot of Texas Instruments OPA2170AIDR Instrumentational OP Amps applications.
- Signal amplification
- Exponential operation circuits
- Ultrasound transducers
- Non-polarized electrodes
- Wireless base stations
- Power generator
- High input resistance broadband
- Communication device
- Power transmission
- Test equipment
