OPA2171AIDCUR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-VFSOP (0.091, 2.30mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 18V |
| Terminal Pitch | 0.5mm |
| Base Part Number | OPA2171 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 18V |
| Number of Elements | 2 |
| Operating Supply Current | 475μA |
| Nominal Supply Current | 475μA |
| Output Current | 25mA |
| Slew Rate | 1.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 104 dB |
| Current - Input Bias | 8pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~36V ±1.35V~18V |
| Output Current per Channel | 35mA |
| Input Offset Voltage (Vos) | 250μV |
| Neg Supply Voltage-Nom (Vsup) | -18V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 130dB |
| Average Bias Current-Max (IIB) | 0.0035μA |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.000015μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 1.8mV |
| Wideband | NO |
| Input Offset Current-Max (IIO) | 0.0035μA |
| Height | 900μm |
| Length | 2.3mm |
| Width | 2mm |
| Thickness | 850μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2171AIDCUR Overview
Packaged in a 8-VFSOP (0.091, 2.30mm Width) case, the buffer op amp is ready to use. This is a General Purpose type op amp. There is a Cut Tape (CT) case that is delivered with the instrumentation amplifiers. In recent months, the number of terminations has approached 8. A total of 8 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 18V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. It has 8 pins that make up the linear amplifier. There is an input offset voltage of 250μV for this buffer op amp. This electronic part is best mounted with type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . This op amp can operate from a supply current at 475μA. 130dB should remain the voltage gain. On the output type, there are Rail-to-Rail different types of op amps. There is a rating of 2 for the operating supply voltage of the buffer op amp. The operating supply voltage of instrumentation amplifier is rated 18V voltage. The instrumentation amplifier is packed in the form of TR.
OPA2171AIDCUR Features
8 Pins
supply voltage of 18V
130dB voltage gain
Output Type: Rail-to-Rail
OPA2171AIDCUR Applications
There are a lot of Texas Instruments OPA2171AIDCUR Instrumentational OP Amps applications.
- Signal operation
- High gain DC amplifier
- Tablets
- Proportional counter tubes
- Multimedia playback equipment
- MP3
- Non-polarized electrodes
- Weak signal detection
- Division circuits
- Semiconductor detectors
