OPA2171AIDCUT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-VFSOP (0.091, 2.30mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 18V |
| Terminal Pitch | 0.5mm |
| Base Part Number | OPA2171 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 18V |
| Number of Channels | 2 |
| Operating Supply Current | 475μA |
| Nominal Supply Current | 475μA |
| Output Current | 25mA |
| Slew Rate | 1.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 104 dB |
| Current - Input Bias | 8pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~36V ±1.35V~18V |
| Output Current per Channel | 35mA |
| Input Offset Voltage (Vos) | 250μV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -18V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 130dB |
| Average Bias Current-Max (IIB) | 0.0035μA |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 1MHz |
| Bias Current-Max (IIB) @25C | 0.000015μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 1.8mV |
| Input Offset Current-Max (IIO) | 0.0035μA |
| Height | 900μm |
| Length | 2.3mm |
| Width | 2mm |
| Thickness | 850μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2171AIDCUT Overview
Op amp is packaged in 8-VFSOP (0.091, 2.30mm Width) case. An op amp of this type is a General Purpose-type. A Cut Tape (CT) case is used to deliver the buffer op amp. It is estimated that there will be at least 8 terminations this year. Buffer amplifier has a total of 8 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 18V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 8 pins are available on the instrumentation amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 250μV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. The buffer amplifier is capable of operating from a supply current of 475μA . There should be no change in the voltage gain at 130dB. There are a total of 2 channels available on the op amps. On the output type, there are Rail-to-Rail different types of op amps. The operating supply voltage of instrumentation amplifier is rated 18V voltage. To pack the operational amplifier ics, TR is adopted as the packing method.
OPA2171AIDCUT Features
8 Pins
supply voltage of 18V
130dB voltage gain
Output Type: Rail-to-Rail
OPA2171AIDCUT Applications
There are a lot of Texas Instruments OPA2171AIDCUT Instrumentational OP Amps applications.
- Measurements of Wheatstone bridge
- Multiplication circuits
- earphone
- Signal amplification
- Television broadcasting equipment
- Test and measurement instruments
- High input resistance broadband
- Active probe
- Mobile phone
- Micro signal measurement
