OPA2228P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | OPA2228 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Elements | 2 |
| Power Supplies | +-5/+-15V |
| Operating Supply Current | 3.7mA |
| Nominal Supply Current | 3.8mA |
| Output Current | 45mA |
| Slew Rate | 11V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 2.5nA |
| Voltage - Supply, Single/Dual (±) | 5V~36V ±2.5V~18V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 75μV |
| Bandwidth | 33MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 33000 kHz |
| Voltage Gain | 160dB |
| Average Bias Current-Max (IIB) | 0.01μA |
| Power Supply Rejection Ratio (PSRR) | 126.02dB |
| Low-Offset | YES |
| Frequency Compensation | YES AVCL>=5 |
| Voltage - Input Offset | 5μV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.01μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 33MHz |
| Max I/O Voltage | 75μV |
| Input Offset Current-Max (IIO) | 0.01μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2228P Overview
Op amp is packaged in 8-DIP (0.300, 7.62mm) case. This is a General Purpose type op amp. The op amp is delivered to you in a Tube case. The number of terminations approaches 8. A total of 8 pins are located on this board. Please take in mind that this instrumentation amplifier should be run at 15V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 8 pins are located on the operational amplifiers. In terms of input offset voltage, operational amplifier rates 75μV. For this electrical component, Through Hole is the recommended mounting type. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . You can run this op amp ic on 3.7mA . There should be no change in the voltage gain at 160dB. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 2. The operating supply voltage of instrumentation amplifier is rated 18V voltage.
OPA2228P Features
8 Pins
supply voltage of 15V
160dB voltage gain
OPA2228P Applications
There are a lot of Texas Instruments OPA2228P Instrumentational OP Amps applications.
- Multimedia playback equipment
- Addition operation circuits
- Industrial applications including automation
- Blood pressure sensors
- Proportional operation circuits
- Scintillation detectors
- Hand-held batteries
- Television
- Radiation thermometry transducers
- Proportional counter tubes
