OPA2228PA
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 16 hours ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | OPA2228 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Power Supplies | +-5/+-15V |
| Number of Channels | 2 |
| Operating Supply Current | 3.7mA |
| Nominal Supply Current | 3.8mA |
| Output Current | 45mA |
| Slew Rate | 11V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 2.5nA |
| Voltage - Supply, Single/Dual (±) | 5V~36V ±2.5V~18V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 33MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 33000 kHz |
| Voltage Gain | 160dB |
| Average Bias Current-Max (IIB) | 0.01μA |
| Power Supply Rejection Ratio (PSRR) | 126.02dB |
| Low-Offset | YES |
| Frequency Compensation | YES AVCL>=5 |
| Voltage - Input Offset | 10μV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.01μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 33MHz |
| Max I/O Voltage | 200μV |
| Input Offset Current-Max (IIO) | 0.01μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2228PA Overview
The linear amplifier is packaged in a 8-DIP (0.300, 7.62mm) case. Buffer amps of this type are called General Purpose-types. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. The number of terminations is approaching the 8 mark. A total of 8 pins are attached to buffer op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 8 pins are available on the instrumentation amplifier. The input offset voltage is 200μV. For this electrical component, Through Hole is the recommended mounting type. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureYou can run this op amp ic on 3.7mA . 160dB should remain the voltage gain. Buffer op amp is equipped with 2 channels on the device. The operating supply voltage of the buffer op amp is rated at 18V.
OPA2228PA Features
8 Pins
supply voltage of 15V
160dB voltage gain
OPA2228PA Applications
There are a lot of Texas Instruments OPA2228PA Instrumentational OP Amps applications.
- Navigation
- Band-pass filter
- Cinema or auditorium audio system
- Instrumentation
- Semiconductor detectors
- Measurements of Wheatstone bridge
- Active probe
- Broadcasting
- Power generator
- Television broadcasting equipment
