OPA228P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | OPA228 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 3.7mA |
| Nominal Supply Current | 3.8mA |
| Output Current | 45mA |
| Slew Rate | 11V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 2.5nA |
| Voltage - Supply, Single/Dual (±) | 5V~36V ±2.5V~18V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 75μV |
| Bandwidth | 33MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 33000 kHz |
| Voltage Gain | 160dB |
| Power Supply Rejection Ratio (PSRR) | 126.02dB |
| Low-Offset | YES |
| Frequency Compensation | YES AVCL>=5 |
| Voltage - Input Offset | 5μV |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 33MHz |
| Max I/O Voltage | 75μV |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA228P Overview
Op amp is packaged in 8-DIP (0.300, 7.62mm) case. Buffer amps of this type are called General Purpose-types. A Tube case is used for delivering the op amp. It is estimated that there will be 8 terminations in the next few months. A total of 8 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. In total, the buffer amplifier consists of 8 pins. Regarding input offset voltage, buffer amplifier rates 75μV voltage. For this electrical component, the recommended mounting type is Through Hole, which is the most common. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~85°C . This op amp can operate from a supply current at 3.7mA. There should be no change in the voltage gain. 1 channels are available on the instrumentation amplifier.
OPA228P Features
8 Pins
supply voltage of 15V
160dB voltage gain
OPA228P Applications
There are a lot of Texas Instruments OPA228P Instrumentational OP Amps applications.
- Ultrasound transducers
- Video data acquisition
- Inverse/same-phase proportional circuit
- Automation control systems
- Weak signal detection
- Addition operation circuits
- Signal filtering
- Industrial control system
- Industrial applications including automation
- High-frequency data acquisition systems
