OPA228PA
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | OPA228 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Operating Supply Current | 3.7mA |
| Nominal Supply Current | 3.8mA |
| Output Current | 45mA |
| Slew Rate | 11V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 2.5nA |
| Voltage - Supply, Single/Dual (±) | 5V~36V ±2.5V~18V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 33MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 33000 kHz |
| Voltage Gain | 160dB |
| Power Supply Rejection Ratio (PSRR) | 126.02dB |
| Low-Offset | YES |
| Frequency Compensation | YES AVCL>=5 |
| Voltage - Input Offset | 10μV |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 33MHz |
| Max I/O Voltage | 200μV |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA228PA Overview
In the package, you will find a 8-DIP (0.300, 7.62mm)-case to contain the op amp ic. A General Purpose-type buffer amplifier is shown here. There is a Tube case that is delivered with the instrumentation amplifiers. In recent months, the number of terminations has approached 8. Linear amplifier has a total of 8 pins. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. Linear amplifier includes 8 pins. As far as the input offset voltage is concerned, linear amplifier rates at 200μV. For this electronic part, it is recommended that you mount it with type Through Hole. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. In order for this instrumentation amplifier to operate, the supply current needs to be between 3.7mA and 10 . There should be no change in the voltage gain at 160dB. As far as the device is concerned, buffer amplifier has 1 channels. The operating supply voltage of instrumentation amplifier is rated 18V voltage.
OPA228PA Features
8 Pins
supply voltage of 15V
160dB voltage gain
OPA228PA Applications
There are a lot of Texas Instruments OPA228PA Instrumentational OP Amps applications.
- Communication
- Test and measurement instruments
- High input resistance broadband
- MP3
- Switching amplifier
- Precision measurement
- Polarized electrodes
- Band-pass filter
- Multimedia playback equipment
- Hand-held batteries
