OPA2301AIDGKT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Weight | 25.996513mg |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | OPA2301 |
| Pin Count | 8 |
| Number of Channels | 2 |
| Operating Supply Current | 9.5mA |
| Nominal Supply Current | 24mA |
| Slew Rate | 80V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 0.1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.75V |
| Output Current per Channel | 70mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 150MHz |
| Unity Gain BW-Nom | 150000 kHz |
| Voltage Gain | 106dB |
| Average Bias Current-Max (IIB) | 0.000005μA |
| Power Supply Rejection Ratio (PSRR) | 86.02dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.000005μA |
| Programmable Power | NO |
| Input Offset Current-Max (IIO) | 0.000005μA |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2301AIDGKT Overview
It is packaged in an 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case that protects the operational amplifiers from damage. Op amps are Voltage Feedback types of amplifier on the chip. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. There is a growing number of terminations approaching the number of 8. The pins on this board total to 8 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. It has 8 pins that make up the linear amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 5mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . This op amp can operate from a supply current at 9.5mA. Maintain 106dB as the voltage gain. There are 2 channels on the operational amplifiers. The instrumentation amplifier is packed in the form of TR.
OPA2301AIDGKT Features
8 Pins
supply voltage of 5V
106dB voltage gain
OPA2301AIDGKT Applications
There are a lot of Texas Instruments OPA2301AIDGKT Instrumentational OP Amps applications.
- Signal transformation
- Communication device
- Communication
- Fission chambers
- Band-pass filter
- Mobile phone
- Division circuits
- Blood pressure sensors
- Tablets
- Radar
