OPA2314AIDGK
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | OPA2314 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Operating Supply Current | 150μA |
| Nominal Supply Current | 150μA |
| Output Current | 20mA |
| Slew Rate | 1.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±0.9V~2.75V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 2.5mV |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 128dB |
| Average Bias Current-Max (IIB) | 0.0006μA |
| Power Supply Rejection Ratio (PSRR) | 78dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 500μV |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 3MHz |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 3MHz |
| Max I/O Voltage | 2.5mV |
| Wideband | NO |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2314AIDGK Overview
There is a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case package that contains the instrumentation amplifiers. A General Purpose-type buffer amplifier is shown here. A Tube case is used to deliver the buffer op amp. A total of 8 terminations have been reported in the past few weeks. There are a total of 8 pins on this op amp. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. It has 8 pins that make up the linear amplifier. The input offset voltage is 2.5mV. This electronic part is best mounted with type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. As long as the supply current of the chip does not exceed 150μA, this op amp ic can operate. The voltage gain should stay at 128dB. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. 2 elements make up the design of this buffer amplifier.
OPA2314AIDGK Features
8 Pins
supply voltage of 5V
128dB voltage gain
Output Type: Rail-to-Rail
OPA2314AIDGK Applications
There are a lot of Texas Instruments OPA2314AIDGK Instrumentational OP Amps applications.
- Signal filtering
- High gain DC amplifier
- Portable media players
- Home audio systems
- Automatic control
- Power control
- High/low-pass filter circuit
- Weighing systems
- Video amplifiers
- Multiplication circuits
