OPA2333AIDRBTG4
| Parameters | |
|---|---|
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | OPA2333 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 2.75V |
| Number of Elements | 2 |
| Operating Supply Current | 17μA |
| Nominal Supply Current | 50μA |
| Output Current | 5mA |
| Slew Rate | 0.16V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 106 dB |
| Current - Input Bias | 70pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±0.9V~2.75V |
| Output Current per Channel | 5mA |
| Input Offset Voltage (Vos) | 10μV |
| Bandwidth | 350 kHz |
| Unity Gain BW-Nom | 350 kHz |
| Voltage Gain | 130dB |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 2μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Max I/O Voltage | 10μV |
| Input Offset Current-Max (IIO) | 0.0004μA |
| Height | 1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 880μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-VDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
OPA2333AIDRBTG4 Overview
A 8-VDFN Exposed Pad case is used to package the op amp. Op amps are Zero-Drift types of amplifier on the chip. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. During the past two weeks, there have been close to 8 terminations. There are a total of 8 pins on this op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 8 pins are available on the instrumentation amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 10μV. Surface Mount is the recommended mounting type of operational amplifiers. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureUsing an 17μA supply current, this operational amplifier ics can be operated. There should be no change in the voltage gain. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 2. The operating supply voltage of instrumentation amplifier is rated 2.75V voltage. As a result of this, the buffer amplifier is packed in TR.
OPA2333AIDRBTG4 Features
8 Pins
supply voltage of 5V
130dB voltage gain
Output Type: Rail-to-Rail
OPA2333AIDRBTG4 Applications
There are a lot of Texas Instruments OPA2333AIDRBTG4 Instrumentational OP Amps applications.
- High/low-pass filter circuit
- Comparator
- Large motor controllers
- Power transmission
- Weighing systems
- Test equipment
- Band-pass filter
- Proportional operation circuits
- Voltage regulation circuit
- Wireless base stations
