OPA2335AID
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | OPA2335 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 2.75V |
| Number of Channels | 2 |
| Operating Supply Current | 570μA |
| Nominal Supply Current | 700μA |
| Quiescent Current | 320mA |
| Slew Rate | 1.6V/μs |
| Architecture | CHOPPER-STAB |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 70pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.75V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 5μV |
| Bandwidth | 2MHz |
| Unity Gain BW-Nom | 2000 kHz |
| Voltage Gain | 130dB |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Max I/O Voltage | 5μV |
| Input Offset Current-Max (IIO) | 0.0004μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2335AID Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. This is a Zero-Drift type op amp. In the case of Tube cases, linear amplifier will be delivered. The number of terminations approaches 8. In this case, there are 8 pins on the board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. Instrumentation amplifier is a part of Operational Amplifier. There are 8 pins on this chip. Op amp rates 5μV as input offset voltage. This electronic part is best mounted with type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . It is possible to operate this buffer amplifier from a supply current of 570μA . Maintain 130dB as the voltage gain. The op amp ic has 2 channels on it. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 2.75V. The quiescent current is 320mA.
OPA2335AID Features
8 Pins
supply voltage of 5V
130dB voltage gain
Output Type: Rail-to-Rail
OPA2335AID Applications
There are a lot of Texas Instruments OPA2335AID Instrumentational OP Amps applications.
- Radar
- Car stereo
- Integrator circuits
- Strain gauges
- Subtraction operation circuits
- RF cable systems
- Non-polarized electrodes
- Laptop
- MP3
- Cinema or auditorium audio system
