OPA2336E/250
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Series | MicroAmplifier™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | OPA2336 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 5V |
| Number of Channels | 2 |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 64μA |
| Slew Rate | 0.03V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.3V~5.5V |
| Output Current per Channel | 5mA |
| Input Offset Voltage (Vos) | 125μV |
| Bandwidth | 100 kHz |
| Unity Gain BW-Nom | 100 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 92.04dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7.5V |
| Voltage - Input Offset | 60μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Max I/O Voltage | 125μV |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2336E/250 Overview
The linear amplifier is packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case which makes it easy for the consumer to handle. General Purpose-type instrumentation amplifiers are used in this application. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. It is estimated that there will be at least 8 terminations this year. The pins on this board total to 8 in total. Please take in mind that this instrumentation amplifier should be run at 5V. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. There are 8 pins on this chip. Op amp ic rates 125μV for input offset voltage. Surface Mount is the recommended mounting type for this linear amplifier. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. Using a supply current of 20μA , this buffer op amp will be able to operate. The voltage gain should stay at 115dB. There are 2 channels on the operational amplifiers. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. For the packing of the instrumentation amplifier, TR is adopted. MicroAmplifier? corresponds to linear amplifier's series.
OPA2336E/250 Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
OPA2336E/250 Applications
There are a lot of Texas Instruments OPA2336E/250 Instrumentational OP Amps applications.
- Ultrasound transducers
- Scintillation detectors
- Test and measurement instruments
- Car stereo
- Professional videography
- Differentiator circuits
- Automatic control
- Signal filtering
- earphone
- Integrator circuits
