OPA2336U
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Series | MicroAmplifier™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | OPA2336 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 5V |
| Number of Channels | 2 |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 64μA |
| Slew Rate | 0.03V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.3V~5.5V |
| Output Current per Channel | 5mA |
| Input Offset Voltage (Vos) | 60μV |
| Bandwidth | 100 kHz |
| Unity Gain BW-Nom | 100 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 92.04dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7.5V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Max I/O Voltage | 125μV |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2336U Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. Op amps are General Purpose types of amplifier on the chip. Linear amplifier is delivered in a Tube case. It is estimated that there will be 8 terminations in the next few months. In this case, there are 8 pins on the board. This linear amplifier should be powered by an 5V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. An 8-pin op amp ic is included in the package. Regarding input offset voltage, op amp rates 60μV. Surface Mount is the recommended mounting type for this linear amplifier. With regard to operating temperature, op amp ranges -40°C~85°C. In order for this instrumentation amplifier to operate, the supply current needs to be between 20μA and 10 . Maintain 115dB as the voltage gain. Buffer op amp is equipped with 2 channels on the device. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. Instrumentation amplifiers are numbered by their MicroAmplifier? series.
OPA2336U Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
OPA2336U Applications
There are a lot of Texas Instruments OPA2336U Instrumentational OP Amps applications.
- Vehicle electronics
- Integrator circuits
- High/low-pass filter circuit
- Proportional counter tubes
- PDA
- Non-polarized electrodes
- Industrial control system
- Fission chambers
- ECG equipment
- Automotive sensors
