OPA2340EA/250G4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Series | MicroAmplifier™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | OPA2340 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Nominal Supply Current | 1.9mA |
| Current - Supply | 750μA |
| Slew Rate | 6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 5.5MHz |
| Unity Gain BW-Nom | 5500 kHz |
| Voltage Gain | 124dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 90.46dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 5.5V |
| Voltage - Input Offset | 150μV |
| Current - Output / Channel | 50mA |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Max I/O Voltage | 500μV |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2340EA/250G4 Overview
In order to protect the op amps, a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case is used. Buffer amps of this type are called General Purpose-types. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. It is estimated that there will be 8 terminations in the next few months. It consists of a total of 8 pins in total. It is important to remember that this op amp should be operated at a voltage of 5V volts. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. It has 8 pins that make up the linear amplifier. Regarding input offset voltage, op amp rates 500μV. This electronic part is best mounted with type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. The voltage gain should stay at 124dB. Op amp ic has 2 channels. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. As a result of this, the buffer amplifier is packed in TR. To run supply current of buffer amplifier under 750μA. In this case, MicroAmplifier? represents the instrumentation amplifiers' series number.
OPA2340EA/250G4 Features
8 Pins
supply voltage of 5V
124dB voltage gain
Output Type: Rail-to-Rail
OPA2340EA/250G4 Applications
There are a lot of Texas Instruments OPA2340EA/250G4 Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- Mobile phone
- High/low-pass filter circuit
- Automatic control
- Communication
- Portable media players
- Weak signal detection
- Portable electronic products powered by batteries
- PDA
- Comparator
