OPA2347YZDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-VFBGA, DSBGA |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | OPA2347 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 3/5V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Output Current | 17mA |
| Slew Rate | 0.17V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 0.5pA |
| Voltage - Supply, Single/Dual (±) | 2.3V~5.5V ±1.15V~2.75V |
| Output Current per Channel | 17mA |
| Input Offset Voltage (Vos) | 6mV |
| Unity Gain BW-Nom | 350 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.00001μA |
| Power Supply Rejection Ratio (PSRR) | 84.44dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7.5V |
| Voltage - Input Offset | 2mV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 350 kHz |
| Max I/O Voltage | 6mV |
| Wideband | NO |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 1mm |
| Length | 1.3mm |
| Width | 2.3mm |
| Thickness | 650μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2347YZDT Overview
In order to protect the op amps, a 8-VFBGA, DSBGA case is used. A General Purpose-type buffer amplifier is shown here. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. It is estimated that there will be 8 terminations in the next few months. The total number of pins on linear amplifier is 8. It is important to remember that this op amp should be operated at a voltage of 5V volts. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. 8 pins are available on the instrumentation amplifier. There is an input offset voltage of 6mV for this buffer op amp. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In relation to the operating temperature of this buffer op amp, it works well at an average of -55°C~125°C . You can run this op amp ic on 20μA . There should be no change in the voltage gain. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. It is possible to count 2 elements on this buffer amplifier. The instrumentation amplifier is packed in the form of TR.
OPA2347YZDT Features
8 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
OPA2347YZDT Applications
There are a lot of Texas Instruments OPA2347YZDT Instrumentational OP Amps applications.
- Navigation
- Measurements of Wheatstone bridge
- Automation control systems
- Image computer boards
- Communication
- RF cable systems
- Band-pass filter
- Scintillation detectors
- Semiconductor detectors
- Signal filtering
