Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Weight |
75.891673mg |
Operating Temperature |
-40°C~85°C |
Packaging |
Tape & Reel (TR) |
Series |
MicroAmplifier™ |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
2 (1 Year) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Operational Amplifier |
Packing Method |
TR |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
5V |
Base Part Number |
OPA2350 |
Pin Count |
8 |
Output Type |
Rail-to-Rail |
Number of Channels |
2 |
Operating Supply Current |
5.2mA |
Supply Current-Max |
7.5mA |
Slew Rate |
22V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
74 dB |
Current - Input Bias |
0.5pA |
Voltage - Supply, Single/Dual (±) |
2.5V~5.5V |
Output Current per Channel |
40mA |
Input Offset Voltage (Vos) |
500μV |
Bandwidth |
38MHz |
Unity Gain BW-Nom |
38000 kHz |
Voltage Gain |
122dB |
Average Bias Current-Max (IIB) |
0.00001μA |
Power Supply Rejection Ratio (PSRR) |
87.96dB |
Low-Offset |
YES |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
7V |
Voltage - Input Offset |
150μV |
Low-Bias |
YES |
Micropower |
NO |
Bias Current-Max (IIB) @25C |
0.00001μA |
Programmable Power |
NO |
Max I/O Voltage |
1mV |
Input Offset Current-Max (IIO) |
0.00001μA |
Input Voltage Noise Density |
7nV/sqrt Hz |
Height |
1.75mm |
Length |
4.9mm |
Width |
3.91mm |
Thickness |
1.58mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
OPA2350UA/2K5 Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case. This is a General Purpose type op amp. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. During the past two weeks, there have been close to 8 terminations. In this case, there are 8 pins on the board. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. In total, the buffer amplifier consists of 8 pins. Regarding input offset voltage, op amp rates 500μV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . As long as the supply current of the chip does not exceed 5.2mA, this op amp ic can operate. Op amp is a member of the 122dB's 122dB family. There are 2 channels on the operational amplifiers. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. As a result of this, the buffer amplifier is packed in TR. Buffer op amp series numbers are indicated by the MicroAmplifier?.
OPA2350UA/2K5 Features
8 Pins
supply voltage of 5V
122dB voltage gain
Output Type: Rail-to-Rail
OPA2350UA/2K5 Applications
There are a lot of Texas Instruments OPA2350UA/2K5 Instrumentational OP Amps applications.
- Non-polarized electrodes
- Portable media players
- Semiconductor detectors
- E-book readers
- Wireless base stations
- Hand-held batteries
- Portable electronic products powered by batteries
- Signal amplification
- Polarized electrodes
- Automatic control