OPA2354AQDGKRQ1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | OPA2354 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Operating Supply Current | 4.9mA |
| Nominal Supply Current | 4.9mA |
| Output Current | 100mA |
| Slew Rate | 150V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V ±1.25V~2.75V |
| Output Current per Channel | 100mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 40MHz |
| Unity Gain BW-Nom | 100000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Power Supply Rejection Ratio (PSRR) | 73.98dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7.5V |
| Settling Time | 60 ns |
| Low-Bias | YES |
| Micropower | NO |
| -3db Bandwidth | 250MHz |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 100MHz |
| Max I/O Voltage | 8mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2354AQDGKRQ1 Overview
Op amp is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. An op amp of this type is a Voltage Feedback-type. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. There have been a total of 8 terminations over the past year. There are a total of 8 pins on this op amp. Please take in mind that this instrumentation amplifier should be run at 5V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are located on the operational amplifiers. In terms of input offset voltage, operational amplifier rates 2mV. Surface Mount is the recommended mounting type of operational amplifiers. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. As long as the supply current of the chip does not exceed 4.9mA, this op amp ic can operate. You should keep the voltage gain at 110dB for the time being. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. There is an operating supply voltage rating of 2 for this operational amplifier, which is rated at the manufacturer. To pack the operational amplifier ics, TR is adopted as the packing method. The Automotive, AEC-Q100 stands for the buffer op amp's serial number.
OPA2354AQDGKRQ1 Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
OPA2354AQDGKRQ1 Applications
There are a lot of Texas Instruments OPA2354AQDGKRQ1 Instrumentational OP Amps applications.
- High gain DC amplifier
- Signal amplification
- Proportional counter tubes
- Commercial audio systems
- Test and measurement instruments
- Cinema or auditorium audio system
- Automation control systems
- Video data acquisition
- Medical imaging
- ECG equipment
