OPA2357AIDGSR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | OPA2357 |
| Pin Count | 10 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Operating Supply Current | 4.9mA |
| Supply Current-Max | 6mA |
| Slew Rate | 150V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 56 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V ±1.25V~2.75V |
| Output Current per Channel | 100mA |
| Input Offset Voltage (Vos) | 8mV |
| Bandwidth | 100MHz |
| Unity Gain BW-Nom | 100000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Power Supply Rejection Ratio (PSRR) | 73.98dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 2mV |
| Settling Time | 30 ns |
| Low-Bias | YES |
| Micropower | NO |
| -3db Bandwidth | 250MHz |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Max I/O Voltage | 8mV |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 1.02mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2357AIDGSR Overview
The linear amplifier is packaged in a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) case. There are two types of operational amplifiers in this circuit. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. A total of 10 terminations have been reported in the past few weeks. A total of 10 pins are attached to buffer op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 3V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. A total of 10 pins are present on the instrumentation amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 8mV. This electronic part is recommended for mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureIn order for this instrumentation amplifier to operate, the supply current needs to be between 4.9mA and 10 . Keeping the voltage gain at 110dB is the best course of action. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. The op amp is rated for an operating supply voltage of 2. The operating supply voltage of instrumentation amplifier is rated 5V voltage. For the packing of the instrumentation amplifier, TR is adopted.
OPA2357AIDGSR Features
10 Pins
supply voltage of 3V
110dB voltage gain
Output Type: Rail-to-Rail
OPA2357AIDGSR Applications
There are a lot of Texas Instruments OPA2357AIDGSR Instrumentational OP Amps applications.
- Car stereo
- High/low-pass filter circuit
- Communication device
- Integrator circuits
- MP3
- Oscilloscopes
- High input resistance broadband
- Television
- Video amplifiers
- Scintillation detectors
