Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
10 |
Operating Temperature |
-40°C~125°C |
Packaging |
Cut Tape (CT) |
JESD-609 Code |
e4 |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
2 (1 Year) |
Number of Terminations |
10 |
ECCN Code |
EAR99 |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Operational Amplifier |
Packing Method |
TR |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
3.6V |
Terminal Pitch |
0.5mm |
Base Part Number |
OPA2363 |
Pin Count |
10 |
Output Type |
Rail-to-Rail |
Operating Supply Voltage |
2.75V |
Number of Elements |
2 |
Operating Supply Current |
1.1mA |
Nominal Supply Current |
2.8mA |
Slew Rate |
5V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
74 dB |
Current - Input Bias |
1pA |
Voltage - Supply, Single/Dual (±) |
1.8V~5.5V ±0.9V~2.75V |
Output Current per Channel |
85mA |
Input Offset Voltage (Vos) |
900μV |
Bandwidth |
7MHz |
Unity Gain BW-Nom |
7000 kHz |
Voltage Gain |
100dB |
Average Bias Current-Max (IIB) |
0.00001μA |
Power Supply Rejection Ratio (PSRR) |
81.94dB |
Low-Offset |
YES |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
5.5V |
Low-Bias |
YES |
Micropower |
NO |
Bias Current-Max (IIB) @25C |
0.00001μA |
Programmable Power |
NO |
Max I/O Voltage |
2.5mV |
Input Offset Current-Max (IIO) |
0.00001μA |
Height |
1.07mm |
Length |
3mm |
Width |
3mm |
Thickness |
1.02mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
OPA2363IDGST Overview
It is packaged in an 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)-case that protects the operational amplifiers from damage. This is a General Purpose type op amp. Instrumentation amplifier is delivered in a Cut Tape (CT) case. There have been a total of 10 terminations over the past year. In this case, there are 10 pins on the board. I would like to remind you that this buffer op amp should be powered by an 3.6V battery. It should be noted that this op amp is a type of Operational Amplifier device. The op amp ic has an array of 10 pins on it. In terms of input offset voltage, operational amplifier rates 900μV. The mounting type that is recommended for this electrical part is Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureAs long as the supply current of the chip does not exceed 1.1mA, this op amp ic can operate. 100dB should be the voltage gain. On the output type, there are Rail-to-Rail different types of op amps. There are 2 elements in total in this linear amplifier. The operating supply voltage of instrumentation amplifier is rated 2.75V voltage. The linear amplifier is packaged by using a TR axis.
OPA2363IDGST Features
10 Pins
supply voltage of 3.6V
100dB voltage gain
Output Type: Rail-to-Rail
OPA2363IDGST Applications
There are a lot of Texas Instruments OPA2363IDGST Instrumentational OP Amps applications.
- Thermocouples
- RF cable systems
- Mobile phone
- Differentiator circuits
- Addition operation circuits
- Voltage regulation circuit
- Large motor controllers
- Medical instruments
- Power generator
- Automatic control