Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 1 week ago) |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Operating Temperature |
-40°C~125°C |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
2 (1 Year) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Operational Amplifier |
Packing Method |
TR |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
3.6V |
Terminal Pitch |
0.65mm |
Base Part Number |
OPA2364 |
Pin Count |
8 |
Output Type |
Rail-to-Rail |
Operating Supply Voltage |
2.75V |
Number of Elements |
2 |
Operating Supply Current |
1.1mA |
Nominal Supply Current |
2.8mA |
Slew Rate |
5V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
74 dB |
Current - Input Bias |
1pA |
Voltage - Supply, Single/Dual (±) |
1.8V~5.5V ±0.9V~2.75V |
Output Current per Channel |
85mA |
Input Offset Voltage (Vos) |
2.5mV |
Bandwidth |
7MHz |
Unity Gain BW-Nom |
7000 kHz |
Voltage Gain |
100dB |
Average Bias Current-Max (IIB) |
0.00001μA |
Power Supply Rejection Ratio (PSRR) |
81.94dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
5.5V |
Voltage - Input Offset |
1mV |
Low-Bias |
YES |
Micropower |
NO |
Bias Current-Max (IIB) @25C |
0.00001μA |
Programmable Power |
NO |
Max I/O Voltage |
2.5mV |
Input Offset Current-Max (IIO) |
0.00001μA |
Height |
1.07mm |
Length |
3mm |
Width |
3mm |
Thickness |
970μm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
OPA2364AIDGKTG4 Overview
Packaging for the buffer amplifier is in the form of a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. An op amp ic of the General Purpose type. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. A total of 8 terminations have been reported in the past few weeks. The pins on this board total to 8 in total. Please take in mind that op amp should be run at 3.6V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. Linear amplifier includes 8 pins. As far as the input offset voltage is concerned, linear amplifier rates at 2.5mV. For this electronic part, it is recommended that you mount it with type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . An 1.1mA volt supply current is needed for this linear amplifier to operate. It is a member of the 100dB's 100dB family. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The op amp is rated for an operating supply voltage of 2. The operating supply voltage of instrumentation amplifier is rated 2.75V voltage. This linear amplifier pack is based on the TR axis.
OPA2364AIDGKTG4 Features
8 Pins
supply voltage of 3.6V
100dB voltage gain
Output Type: Rail-to-Rail
OPA2364AIDGKTG4 Applications
There are a lot of Texas Instruments OPA2364AIDGKTG4 Instrumentational OP Amps applications.
- Mobile phone
- Car stereo
- Band-pass filter
- Semiconductor detectors
- Inverse/same-phase proportional circuit
- Subtraction operation circuits
- earphone
- High/low-pass filter circuit
- Information processing
- E-book readers