OPA2373AIDRCT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | OPA2373 |
| Pin Count | 10 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Number of Circuits | 2 |
| Operating Supply Current | 585μA |
| Supply Current-Max | 1.5mA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 0.5pA |
| Voltage - Supply, Single/Dual (±) | 2.3V~5.5V ±1.15V~2.75V |
| Input Offset Voltage (Vos) | 5mV |
| Unity Gain BW-Nom | 6500 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00001μA |
| Power Supply Rejection Ratio (PSRR) | 92.04dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 6.5MHz |
| Max I/O Voltage | 5mV |
| Wideband | NO |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2373AIDRCT Overview
Packaging for the buffer amplifier is in the form of a 10-VFDFN Exposed Pad case. An op amp of this type is a General Purpose-type. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. A total of 10 terminations have been reported in the past few weeks. The pins on this board total to 10 in total. This linear amplifier should be powered by an 5V battery. Instrumentation amplifier is a part of Operational Amplifier. 10 pins are included on the operational amplifiers. Op amp ic rates 5mV for input offset voltage. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureUsing a supply current of 585μA , this buffer op amp will be able to operate. Maintain 110dB as the voltage gain. On this instrumentation amplifier, there are 2 circuits that are connected together. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. As a whole, there are 2 elements that make up this buffer amplifier. It is used TR to pack the op amps.
OPA2373AIDRCT Features
10 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
OPA2373AIDRCT Applications
There are a lot of Texas Instruments OPA2373AIDRCT Instrumentational OP Amps applications.
- Automotive sensors
- Power transmission
- Car stereo
- Medical imaging
- Semiconductor detectors
- High-frequency data acquisition systems
- Polarized electrodes
- Weighing systems
- Micro signal measurement
- Video data acquisition
