OPA2376AID
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Series | e-trim™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.2V |
| Base Part Number | OPA2376 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Operating Supply Current | 760μA |
| Nominal Supply Current | 950μA |
| Slew Rate | 2V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 76 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 2.2V~5.5V ±1.1V~2.75V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 25μV |
| Bandwidth | 5.5MHz |
| Unity Gain BW-Nom | 5500 kHz |
| Voltage Gain | 134dB |
| Average Bias Current-Max (IIB) | 0.00001μA |
| Power Supply Rejection Ratio (PSRR) | 106.02dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 5μV |
| Settling Time | 1.6 μs |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Max I/O Voltage | 25μV |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2376AID Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the General Purpose-type. In the case of Tube cases, linear amplifier will be delivered. The number of terminations approaches 8. A total of 8 pins are located on this board. As a reminder, this buffer op amp should be powered by 2.2V battery and that the battery should be inserted in the amplifier. It should be noted that this op amp is a type of Operational Amplifier device. A total of 8 pins are present on the instrumentation amplifier. Op amp rates 25μV as input offset voltage. This electronic part is best mounted with type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. An 760μA volt supply current is needed for this linear amplifier to operate. Maintain 134dB as the voltage gain. On the buffer amps, there are 2 channels that can be used. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. Instrumentation amplifiers are numbered by their e-trim? series.
OPA2376AID Features
8 Pins
supply voltage of 2.2V
134dB voltage gain
Output Type: Rail-to-Rail
OPA2376AID Applications
There are a lot of Texas Instruments OPA2376AID Instrumentational OP Amps applications.
- Differentiator circuits
- ECG equipment
- High speed sample
- single/dual op amp sum and difference circuits
- Video conversion and routing
- Laptop
- Weak signal detection
- Communication device
- Scintillation detectors
- Active probe
