Parameters |
Package / Case |
8-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C |
Packaging |
Tube |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Operational Amplifier |
Technology |
BIPOLAR |
Terminal Position |
DUAL |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
2.54mm |
Base Part Number |
OPA241 |
Pin Count |
8 |
Output Type |
Rail-to-Rail |
Operating Supply Voltage |
18V |
Number of Channels |
1 |
Operating Supply Current |
27μA |
Nominal Supply Current |
30μA |
Slew Rate |
0.01V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
80 dB |
Current - Input Bias |
4nA |
Voltage - Supply, Single/Dual (±) |
2.7V~36V ±1.35V~18V |
Output Current per Channel |
21mA |
Input Offset Voltage (Vos) |
250μV |
Bandwidth |
35MHz |
Unity Gain BW-Nom |
35 kHz |
Voltage Gain |
120dB |
Average Bias Current-Max (IIB) |
0.025μA |
Low-Offset |
YES |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
36V |
Voltage - Input Offset |
100μV |
Low-Bias |
NO |
Micropower |
YES |
Bias Current-Max (IIB) @25C |
0.02μA |
Programmable Power |
NO |
Dual Supply Voltage |
9V |
Nominal Gain Bandwidth Product |
35 kHz |
Max I/O Voltage |
250μV |
Power |
NO |
Input Offset Current-Max (IIO) |
0.002μA |
Height |
5.08mm |
Length |
9.81mm |
Width |
6.35mm |
Thickness |
3.9mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Mounting Type |
Through Hole |
OPA241PA Overview
There is a 8-DIP (0.300, 7.62mm) case package that contains the instrumentation amplifiers. Op amps are General Purpose types of amplifier on the chip. The case in which buffer amplifier is delivered is called a Tube case. A total of 8 terminations have been reported in the past few weeks. Buffer amplifier has a total of 8 pins. Please take in mind that op amp should be run at 5V. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 8 pins are located on the operational amplifiers. Regarding input offset voltage, buffer amplifier rates 250μV voltage. This electronic part is recommended for mounting type Through Hole. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. A supply current of 27μA can be used to operate this linear amplifier. 120dB should remain the voltage gain. There are 1 channels on the operational amplifiers. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 18V voltage.
OPA241PA Features
8 Pins
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
OPA241PA Applications
There are a lot of Texas Instruments OPA241PA Instrumentational OP Amps applications.
- Digital cameras
- Information processing
- Displayers for aircraft and air transportation control systems
- Automotive sensors
- Navigation
- Proportional operation circuits
- MP3
- Broadcasting
- Vehicle electronics
- Addition operation circuits