OPA2544TG3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Through Hole |
| Package / Case | TO-220-11 (Formed Leads) |
| Surface Mount | NO |
| Number of Pins | 11 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 11 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Terminal Position | ZIG-ZAG |
| Number of Functions | 2 |
| Supply Voltage | 35V |
| Terminal Pitch | 1.7mm |
| Base Part Number | OPA2544 |
| Pin Count | 3 |
| Operating Supply Voltage | 35V |
| Number of Channels | 2 |
| Operating Supply Current | 22mA |
| Nominal Supply Current | 30mA |
| Output Current | 2A |
| Slew Rate | 8V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 15pA |
| Voltage - Supply, Single/Dual (±) | ±10V~35V |
| Output Current per Channel | 4A |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 1.4MHz |
| Neg Supply Voltage-Nom (Vsup) | -35V |
| Unity Gain BW-Nom | 1400 kHz |
| Voltage Gain | 103dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1.4MHz |
| Max I/O Voltage | 5mV |
| Power | YES |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Height | 4.62mm |
| Length | 20.02mm |
| Width | 10.7mm |
| Thickness | 4.5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2544TG3 Overview
In the package, you will find a TO-220-11 (Formed Leads)-case to contain the op amp ic. Op amps are General Purpose types of amplifier on the chip. A Tube case is used for delivering the op amp. It is estimated that there will be 11 terminations in the next few months. A total of 3 pins are located on this board. Please take in mind that op amp should be run at 35V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. An 11-pin op amp ic is included in the package. Regarding input offset voltage, op amp rates 5mV. This electronic component is recommended to be mounted using the mounting type Through Hole. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureYou can run this op amp ic on 22mA . Voltage gain should remain at 103dB. There are a total of 2 channels available on the op amps. The operating supply voltage of the buffer op amp is rated at 35V.
OPA2544TG3 Features
3 Pins
supply voltage of 35V
103dB voltage gain
OPA2544TG3 Applications
There are a lot of Texas Instruments OPA2544TG3 Instrumentational OP Amps applications.
- Ultrasound transducers
- Micro signal measurement
- Large motor controllers
- Biopotential
- Strain gauges
- Signal transformation
- Inverse/same-phase proportional circuit
- Multiplication circuits
- Multimedia playback equipment
- Radiation thermometry transducers
