OPA2677IDDA
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-PowerSOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 70.590313mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Series | SpeedPlus™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 6V |
| Base Part Number | OPA2677 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Operating Supply Current | 18mA |
| Slew Rate | 2000V/μs |
| Amplifier Type | Current Feedback |
| Common Mode Rejection Ratio | 49 dB |
| Current - Input Bias | 10μA |
| Voltage - Supply, Single/Dual (±) | 5V~12V ±2.5V~6V |
| Output Current per Channel | 500mA |
| Input Offset Voltage (Vos) | 3.5mV |
| Bandwidth | 220MHz |
| Gain Bandwidth Product | 2GHz |
| Neg Supply Voltage-Nom (Vsup) | -6V |
| Unity Gain BW-Nom | 220000 kHz |
| Average Bias Current-Max (IIB) | 35μA |
| Power Supply Rejection Ratio (PSRR) | 52dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1mV |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 250MHz |
| Bias Current-Max (IIB) @25C | 30μA |
| Programmable Power | NO |
| Dual Supply Voltage | 6V |
| Max I/O Voltage | 5.5mV |
| Height | 1.7mm |
| Length | 4.89mm |
| Width | 3.9mm |
| Thickness | 1.48mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2677IDDA Overview
There is a 8-PowerSOIC (0.154, 3.90mm Width) case package that contains the instrumentation amplifiers. A Current Feedback-type buffer amplifier is shown here. Upon delivery, op amp ic is packaged in a Tube case. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are attached to buffer op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 6V. Instrumentation amplifier is a part of Operational Amplifier. The op amp ic has an array of 8 pins on it. With regards to the offset voltage of the input, buffer amplifier is rated at 3.5mV. For this electrical component, Surface Mount is the recommended mounting type. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~85°C . Using an 18mA supply current, this operational amplifier ics can be operated. There are a total of 2 elements in this linear amplifier. The operating supply voltage of the buffer op amp is rated at 5V. Instrumentation amplifiers are numbered by their SpeedPlus? series.
OPA2677IDDA Features
8 Pins
supply voltage of 6V
OPA2677IDDA Applications
There are a lot of Texas Instruments OPA2677IDDA Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- RF cable systems
- Proportional counter tubes
- Measurements of Wheatstone bridge
- Signal operation
- ECG equipment
- Voltage regulation circuit
- Gaming industry
- Scintillation detectors
- Power transmission
