OPA2705PA
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | OPA2705 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 6V |
| Number of Elements | 2 |
| Operating Supply Current | 160μA |
| Nominal Supply Current | 500μA |
| Output Current | 10mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 4V~12V ±2V~6V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.00001μA |
| Power Supply Rejection Ratio (PSRR) | 93.98dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Max I/O Voltage | 5mV |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2705PA Overview
The linear amplifier is packaged in a 8-DIP (0.300, 7.62mm) case which makes it easy for the consumer to handle. Op amps are General Purpose types of amplifier on the chip. The case in which buffer amplifier is delivered is called a Tube case. A total of 8 terminations have been reported in the past few weeks. There are a total of 8 pins on this op amp. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 8 pins are located on the operational amplifiers. Op amp rates 5mV as input offset voltage. Through Hole is the recommended mounting type for this linear amplifier. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureUsing an 160μA supply current, this operational amplifier ics can be operated. You should keep the voltage gain at 120dB for the time being. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The op amp is rated for an operating supply voltage of 2. The operating supply voltage of the buffer op amp is rated at 6V.
OPA2705PA Features
8 Pins
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
OPA2705PA Applications
There are a lot of Texas Instruments OPA2705PA Instrumentational OP Amps applications.
- MP3
- Comparator
- Radiation thermometry transducers
- PDA
- Computer workstations
- Multimedia playback equipment
- Portable docking station
- Differentiator circuits
- Signal transformation
- Hand-held batteries
