OPA2705UAG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | OPA2705 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 6V |
| Number of Elements | 2 |
| Operating Supply Current | 160μA |
| Nominal Supply Current | 500μA |
| Output Current | 10mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 4V~12V ±2V~6V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.00001μA |
| Power Supply Rejection Ratio (PSRR) | 93.98dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Max I/O Voltage | 5mV |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2705UAG4 Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. Buffer amps of this type are called General Purpose-types. In the case of Tube cases, linear amplifier will be delivered. It is estimated that there will be at least 8 terminations this year. In this case, there are 8 pins on the board. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 8 pins are located on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 5mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureYou can run this op amp ic on 160μA . Op amp is a member of the 120dB's 120dB family. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. For the operating supply voltage of the op amp ic, there is a rating of 2. The operating supply voltage of instrumentation amplifier is rated 6V voltage.
OPA2705UAG4 Features
8 Pins
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
OPA2705UAG4 Applications
There are a lot of Texas Instruments OPA2705UAG4 Instrumentational OP Amps applications.
- Image computer boards
- High input resistance broadband
- Differentiator circuits
- Video computer boards
- Wireless base stations
- Medical instruments
- Integrator circuits
- High speed sample
- Thermocouples
- Radiation thermometry transducers
